How to Open a Pool

Step 1: Remove any debris and inspect the area for damages that may be present

Examine the surroundings of your pool before you open your swimming pool. Trim any overgrown hedges and trees. Remove any nearby leaves with the help of a broom. Before opening your pool for the season, inspect your deck for damages, wear, and tear and take any necessary repairs. To ensure that any deck furniture is safe to use, be sure to clean and repair it. You should also inspect the pool’s safety rails, slides, rescue tools, ladders, and diving boards before opening your swimming pool.

Step 2: Measure the chemicals in your pool.

Before starting to open your pool, you should have all of your chemicals ready to go.

Checklist for Chemicals:

Need to make a supply run for pool chemicals prior to opening? What you’ll need to finish the project properly is listed below:

• A reliable test kit or set of test strips for analyzing the water chemistry in your pool
• For daily sanitizing, use chlorine
• Shock therapy
• Chemicals for correctly correcting the water balance in your pool
• Algicide application
• Filter cleanser or further required problem prevention tools

Step 3: Take Off the Cover of Your Pool

Your pool cover may collect water and debris throughout the course of the fall and winter. To remove that stale, unclean water and keep it out of your swimming pool, use a pool cover pump. Once the cover has been taken off, thoroughly clean it with a hose using a cleanser that has been carefully prepared, such PoolStyle Clean-N-Store, and then let it air dry.

Keeping your pool cover properly

By keeping it secure and out of the reach of animals, pests, and the elements, you can extend the life of your pool cover to a certain point. Once your pool cover is clean and dry, roll it up firmly and keep it inside or in a garage.

Step 4: Diminish the Heavy Metal

Contrary to common sense, metal levels may have risen in your pool’s water as it sat still all winter.

You presumably also just filled your pool with tap water to the top. We hope that a hose filter was employed to help keep the minerals out of your pool. However, you should add a metal sequestrant if there is any metal in your pool water to prevent stains and accumulation.

Step 5: Check the pool

It’s crucial to thoroughly inspect your pool before you open it for the season. You should include the tasks listed below on your list of top priorities:

• Surface skimmers and wall returns should have drain plugs or winterizing plugs removed, and directed fittings should be put back in place.
• Look for any possible worn or damaged parts on the filter and pump, and replace as necessary.
• It’s time to reattach any underwater pool lights you may have already removed.
• Check your pool’s coating and decking for any irregularities, damages or signs of wear.
• Examine your tile and use the right swimming pool scale removal product to eliminate calcium buildup and discoloration. For advice on the best products to use, you can always contact Nachman Pool Opening Company for your sanctuaries located in Virginia and Maryland.
• Check your pool’s interior for damage, and make any necessary repairs.

Fiberglass Pools and Hairline Cracks

In fiberglass pools, it is normal to see hairline cracks. These little cracks usually won’t have an impact on the structural integrity of your pool because fiberglass pools have a gel covering. However, you should contact your neighborhood pool company immediately away if your fiberglass pool has noticeable fractures or holes.

Step 6: Complete the Final Debris Removal and Fill the Pool to the Tile’s Waterline

Use a garden hose to fill the pool until the water level reaches the center of the skimmer aperture or the waterline tile. Once the water level is where it needs to be, you can use a pool brush to remove leaves, twigs, and other debris from the pool’s bottom. You should make sure to clean the basket of any trash as well.

Step 7: Turn On the Pool Filter First, Then Test the Water in Your Pool

You are so close to your goal! Get the filter functioning right away is all that’s left to do. Before conducting tests or adding chemicals, turn on the filter and let it run for 12 to 24 hours to recirculate the water (avoid the expired testing strips and try to use new ones).

It is advised to have a professional water test performed when your pool is first opened and once a month thereafter for the duration of the season. A pool expert at Nachman Pool Opening Company is always available to examine a water sample for you for your properties in Virginia, Maryland, and other states. The steps to balance your pool’s water will be given to you by your pool specialist.

Nachman Pool Company is available to check the pH, alkalinity, calcium hardness, and chlorine content of the water of your pool. We are able to advise you to add a stabilizer, phosphate remover, metal treatment solution, or algaecide to your pool before it is prepared for the warm summer season in addition to shocking the pool.

Run the filter continuously for a few days while vacuuming up any collected material. Your pool is suitable for swimming when the water is clear and the chlorine levels have decreased. Have fun in your pool all summer along!

Keeping Your Pool’s Chemistry Balanced During the Swimming Season

Do not forget to test the water in your pool every week and to bring it to your neighborhood pool specialist once a month or whenever you are facing problems with it.  The best maintenance procedures will maintain the water in your pool clear and guard against unhealthy water quality conditions. Don’t forget to shock regularly or weekly to eliminate pollutants, sanitize daily, and apply a small preventative dosage of algaecide once per week to stop algae outbreaks.

A Piece of Advice for you: Remember to make sure to look for damages, cracks, or leaks in your filter and return lines. If necessary, add sand to your sand filter. If your filter is a cartridge, examine it and clean or replace it as necessary.

Get an Appointment